Parts New! The Garage  

 

WELCOME TO THE RME GARAGE

Return to Home Page

Have an item to sell?

Interested in a Garage Item?

Disclaimers / Exceptions:

RME conveying information as it is received by the seller.  All information is believed to be true but not guaranteed.  Buyer must carefully review the product and details prior to the purchase.

The Roberts Mechanical Equipment Company Shall "NOT" take responsibility for the following:

  • Any cost associated with shipping, rigging, or installation of Garage items.

  • Any warranty, repair, or replacement of used or 'as is' equipment listed in The Garage.

  • Damage or injury caused by equipment failure.

  • Damage or injury caused by improper application, installation, or operation of listed equipment.

  • Start up of the equipment unless specifically agreed upon at the time of purchase.

  • Applicable taxes, permits, or licenses required to purchase, install or operate equipment.

All items listed on this page should be considered 'as is'.  Buyers should take care to research and evaluate the condition of the equipment prior to his purchase.

Items on this page are not returnable or refundable.

The equipment manufacturer or the owner of the equipment shall be responsible for any other issues not listed on this site. 

Offerings on this page are not available where terms, conditions, disclaimers, and exceptions are prohibited by laws both local or federal.  Buyer takes full responsibility for all legal ramifications based on the sale of garage items.

Terms and conditions listed here are not all inclusive.  Other terms and conditions may apply.  Finance terms and conditions may not be available on Garage items.  Check with the listing agent.
 

RME often has access to overstocked, scratch and dent, or used equipment, products and tools.  This area of our web site is intended to share this information with our customer base, but also to give our customers an opportunity to post some of their related equipment on our page.  Not all the items below are owned by RME.  You should contact the listing agent to find out more information about the equipment.  Each item is treated separately, and no warranty on these items should be implied or assumed without a written statement at the time of purchase.

 

 

 

 

 

 

 

 

Text Box: Currently 'In The Garage': If any of the following used, scratch and dent, or overstocked items interest you, contact our Cleveland office for Details:   Available Equipment/Tools: Asking Price and Listing Agent: Equipment Details and Instruction: Picture if Available:   Deaerating Feed Water System Manufactured by PMI Industries Built by George Marker & Sons Capacity - 40,000 lbs/hr water output (minimum) Type - verticle spray tray w/ Horizontal storage tank water in - 110 degrees to 180 degrees F Water out - 220 degrees     Asking:  BEST OFFER Contact:  Dennis Malkin   Design pressure - 30 PSI Operating steam pressure - 2-15 PSIG Deaeration - to 0.005 cc/liter oxygen Storage capacity - 200 cu.ft. minimum at overflow 18.75 minutes at 50 G.P.M. Size - 5' diam x 110' O.A. Construction - ASME code for 30 PSIG Condition - excellent, no pitting Installed 1993, out of service 2005         Transfer System Built by Shipco Built 2005, used 3 months Base - 4' wide, 9' long, 5' high, with 1' extension to accommodate the 2 pumps.  Piping and control panel included. Base will accommodate a variety of tanks Tank is non-rated, 1/4 plate steel, flat ends, 4' diameter, 10' long Pumps are model no. (2) D129 Horizontal End Suction   Asking:  BEST OFFER Contact:  Dennis Malkin   Data:  Operating Flow: 75 GPM Head @ 75 GPM: 20 FT NPSHR @ 75 GPM:  4.2 FT Motor HP: 1 Voltage:    460V/3/60 RPM: 1750 Control panel is included Excellent condition                                                                                                  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  
 
 
     
 

  Roberts Mechanical Equipment - 5031 Turney Rd. - Cleveland OH 44125 - ph: 216.587.0005 - fax: 216.587.0008 - www.robertsmech.com